Quantcast
Channel: Intel Communities : Popular Discussions - Servers
Viewing all 3319 articles
Browse latest View live
↧

Intel S5520hc fans are always running full speed

June 23, 2017, 4:35 am
$
0
0

Im standing with a server, with the Intel S5520hc board. And whenever i turn it on, the fans start spinning at full speed. It takes about 10 seconds, before the fans kick in, and after that they never slow down again.
The first thing we did was to go in under the bios, and change the advanced, System Acoustics and Performance Configuration, Set Throttling Mode from CLTT to OLTT. But whenever it restarts it just changes back. We tried updating the

FRUDSR, tried updating the bios to the newest version, tried unplugging and plugging back in the fan pins. None of it helped, we checked with SEL for any failures. Attached is the .sel file we get from the server, removed previous dates. All we could see was that it looped the same 3 messages for each of the 3 fans.

 

Informational event: System Fan 1 reports the sensor is no longer in a critically low state.  Sensor reading: Unspecified.  Threshold value: Unspecified.

Warning event: System Fan 1 reports the sensor is in a low, but non-critical, and going lower state.  Sensor reading: 0.000000 RPM.  Threshold value: 380.000000 RPM.

CRITICAL event: System Fan 1 reports the sensor is in a low, critical, and going lower state.  Sensor reading: 0.000000 RPM.  Threshold value: 320.000000 RPM.

 

Specs:

CategoryItem
MotherboardS5520HC
CPU2X Intel Xeon X560 @ 2.67GHz
CPUFans2X Intel E97383-002
↧
Search

first start problem

October 28, 2013, 7:25 am
$
0
0

I had created a operating software from bootable usb device but I am getting this error: "Initializing and Establishing Link"  . I am using a SR1550AL server and I thing I should disable network from bios but couldnt find disable option any help about it?

↧
↧

S5520HC EFI Optimized Boot

June 21, 2017, 5:05 am
$
0
0

Hi,

I have difficulties with EFI Boot.

Long story short:

Having BIOS revision R0064 I'm trying to boot OS V 10.11 El Capitan.

The process is trail/error, so I need an easy way to change the BIOS Boot mode between MBR/EFI.

It is because I'm not sure I have proper disk for EFI boot, although I've got an OS X 10.11 installed on the machine and it doesn't boot in MBR mode, but if I set EFI Optimized Boot and try to boot my installation I don't have an success. The error code is 0xD6 - Trying boot selection.

The worst thing is I don't have an access to the BIOS Set Up at all so, I have to recover or update the BIOS to get the system working.

 

Any ideas?

Thanks.

↧

Intel S5520hc fans are always running full speed

June 23, 2017, 4:35 am
$
0
0

Im standing with a server, with the Intel S5520hc board. And whenever i turn it on, the fans start spinning at full speed. It takes about 10 seconds, before the fans kick in, and after that they never slow down again.
The first thing we did was to go in under the bios, and change the advanced, System Acoustics and Performance Configuration, Set Throttling Mode from CLTT to OLTT. But whenever it restarts it just changes back. We tried updating the

FRUDSR, tried updating the bios to the newest version, tried unplugging and plugging back in the fan pins. None of it helped, we checked with SEL for any failures. Attached is the .sel file we get from the server, removed previous dates. All we could see was that it looped the same 3 messages for each of the 3 fans.

 

Informational event: System Fan 1 reports the sensor is no longer in a critically low state.  Sensor reading: Unspecified.  Threshold value: Unspecified.

Warning event: System Fan 1 reports the sensor is in a low, but non-critical, and going lower state.  Sensor reading: 0.000000 RPM.  Threshold value: 380.000000 RPM.

CRITICAL event: System Fan 1 reports the sensor is in a low, critical, and going lower state.  Sensor reading: 0.000000 RPM.  Threshold value: 320.000000 RPM.

 

Specs:

CategoryItem
MotherboardS5520HC
CPU2X Intel Xeon X560 @ 2.67GHz
CPUFans2X Intel E97383-002
↧

Bricked S2600G(L/Z)?

June 25, 2017, 8:05 am
$
0
0

Hi Guys,

 

So i was trying to upgrade firmware on my server.

I ran flashupdt -u  <package folder name>\flashupdt.cfg and went away when it was "Upgrading HBSP and PSU firmware..."

After i came back the server was running - fans were spinning but no signal on the screen. I left it running for couple of minutes but there was no change so i rebooted the server - it didn't come back.

System Status LED is solid Amber and 2nd,3rd green POST LED is on which means: 06h Early CPU initialisation during Sec Phase. and it stays like that forever.

I tried to swap CPUs, run with only one CPU (both CPUs tested) and the error is always the same.

 

Then i tried to flash using BIOS Recovery Procedure and i'm getting 1st,4th green LED on and 1st,2nd,3rd,4th Amber LED ON with 2 Beeps and 4 Beeps in the background.

I also tried different CPU configuration and nothing helps.

The only difference i see (i think so) is when i have USB drive inserted and not inserted.

When there's no USB Mass Storage beeps happens so quickly as described in the manual but when i insert the USB there's 1 second break between each set of beeps. Maybe i'm doing something wrong?

 

Does it means i bricked motherboard?

↧
↧

Intel H2312JFJR - hardisks are not recognized

June 19, 2017, 12:24 am
$
0
0

Hi,

I bought an intel H2312JFJR system which came with 12 SCSI drives (2TB) and  four HNS2600JF Server Nodes.

When I first powered up the system, I noticed that non of the 12 hard disks is flashing any status light and when I get into the BIOS setup, no harddisk appeared in the boot order menu. This is the case for all the 4 nodes.

I tried to install a hypervisor (Xenserver) from the flash drive and it also confirmed that it could not find any drives. The only way I managed to get a node up and running is by using a flash drive with live Linux image.

I do not have any experience in Intel servers so I am not sure how to proceed.

What would cause all the 12 drives not working despite being a 4 node system with redundancy? and how should I proceed to further diagnose the problem ?

Regards,

Mishal

↧

S5520HC EFI Optimized Boot

June 21, 2017, 5:05 am
$
0
0

Hi,

I have difficulties with EFI Boot.

Long story short:

Having BIOS revision R0064 I'm trying to boot OS V 10.11 El Capitan.

The process is trail/error, so I need an easy way to change the BIOS Boot mode between MBR/EFI.

It is because I'm not sure I have proper disk for EFI boot, although I've got an OS X 10.11 installed on the machine and it doesn't boot in MBR mode, but if I set EFI Optimized Boot and try to boot my installation I don't have an success. The error code is 0xD6 - Trying boot selection.

The worst thing is I don't have an access to the BIOS Set Up at all so, I have to recover or update the BIOS to get the system working.

 

Any ideas?

Thanks.

↧

first start problem

October 28, 2013, 7:25 am
$
0
0

I had created a operating software from bootable usb device but I am getting this error: "Initializing and Establishing Link"  . I am using a SR1550AL server and I thing I should disable network from bios but couldnt find disable option any help about it?

↧
Search

Intel H2312JFJR - hardisks are not recognized

June 19, 2017, 12:24 am
$
0
0

Hi,

I bought an intel H2312JFJR system which came with 12 SCSI drives (2TB) and  four HNS2600JF Server Nodes.

When I first powered up the system, I noticed that non of the 12 hard disks is flashing any status light and when I get into the BIOS setup, no harddisk appeared in the boot order menu. This is the case for all the 4 nodes.

I tried to install a hypervisor (Xenserver) from the flash drive and it also confirmed that it could not find any drives. The only way I managed to get a node up and running is by using a flash drive with live Linux image.

I do not have any experience in Intel servers so I am not sure how to proceed.

What would cause all the 12 drives not working despite being a 4 node system with redundancy? and how should I proceed to further diagnose the problem ?

Regards,

Mishal

↧
↧

May be you can help us we have QSV server with

June 9, 2017, 1:10 am
$
0
0
bios   S1200RP.86B.03.04.0002.110820161604 CPU Intel(R) Xeon(R) CPU E3-1276 v3 @ 3.60GHz  RAM 2x ChannelA-DIMM1 8192 DDR3 1600 Micron 9876543210 1820287218KSF1G72AZ-1G6P1 and we have problem with CATERRProcessorreports it has been asserted - Deasserted
↧

Controller ID: 0 PD Predictive failure Question

January 15, 2013, 6:58 am
$
0
0

My question is how the heck do I determine which drive is about to fail, without having to pull the system offline and run SMART checks on each drive.

Here's the event:

"

Controller ID:  0   PD Predictive failure: 

    Int.Ports 4-7:2:0

Event ID:96

"

 

OS is Server 2008 R2

 

 

Thanks in advance for the assistance.

↧

RAID module RMS25JB080 ESXi drivers

June 26, 2017, 8:27 pm
$
0
0

Hi

 

cant find the VMWare ESXi drivers for the RMS25JB080 RAID module? (it will be in an S1200SPOR board which is fully VMWare supported)

 

Ive had some real major issues with ALL RAID board with ESXi, the only way to get them to fully work is to install the below:

 

RAID drivers, AND the SMIS drivers, with both install the module will show up in the ESXi vSphere console with what drive is attached to which connector on the board.

 

Also should allow for the Intel RAID configuration tool to connect to the board when its running ESXi to configure it, check drive status via the ESXi management IP address.  This has been a MAJOR MAJOR issue for LSI / AVAGO / BROADCOM (what ever there calling themselves now-a-days) RAID cards, i have the drivers here for them now so i dont need to go hunting for them.

 

However i have never done ESXi for Intel RAID cards yet (as there not really LSI / AVAGO / BROADCOM cards now... there a hybrid version.

 

Many Thanks.

↧

S2600CW2R怎样以UEFI启动Windows 7 64bit ？

June 20, 2017, 8:53 am
$
0
0

CPU是 E5-2683 v3，显卡是 GTX 1070，主板的BIOS设置里，UEFI选项下有Vedio BIOS的设置选项，设置成 Legacy，还是不能启动 Windows 7 64bit，QQ截图20170620235107.pngQQ截图20170620235122.pngQQ截图20170620235134.png

↧
↧

Intel H2312JFJR - hardisks are not recognized

June 19, 2017, 12:24 am
$
0
0

Hi,

I bought an intel H2312JFJR system which came with 12 SCSI drives (2TB) and  four HNS2600JF Server Nodes.

When I first powered up the system, I noticed that non of the 12 hard disks is flashing any status light and when I get into the BIOS setup, no harddisk appeared in the boot order menu. This is the case for all the 4 nodes.

I tried to install a hypervisor (Xenserver) from the flash drive and it also confirmed that it could not find any drives. The only way I managed to get a node up and running is by using a flash drive with live Linux image.

I do not have any experience in Intel servers so I am not sure how to proceed.

What would cause all the 12 drives not working despite being a 4 node system with redundancy? and how should I proceed to further diagnose the problem ?

Regards,

Mishal

↧

Found the solution to loud fans when using "other chassis" option when updating Firmware on a server board

May 7, 2010, 12:02 pm
$
0
0

This has been a big headache for a long time with no real solution posted anywhere on the internet.  Am I allowed to post this? It involved editing the SDR file. thanks

↧
Search

Intel S5520hc fans are always running full speed

June 23, 2017, 4:35 am
$
0
0

Im standing with a server, with the Intel S5520hc board. And whenever i turn it on, the fans start spinning at full speed. It takes about 10 seconds, before the fans kick in, and after that they never slow down again.
The first thing we did was to go in under the bios, and change the advanced, System Acoustics and Performance Configuration, Set Throttling Mode from CLTT to OLTT. But whenever it restarts it just changes back. We tried updating the

FRUDSR, tried updating the bios to the newest version, tried unplugging and plugging back in the fan pins. None of it helped, we checked with SEL for any failures. Attached is the .sel file we get from the server, removed previous dates. All we could see was that it looped the same 3 messages for each of the 3 fans.

 

Informational event: System Fan 1 reports the sensor is no longer in a critically low state.  Sensor reading: Unspecified.  Threshold value: Unspecified.

Warning event: System Fan 1 reports the sensor is in a low, but non-critical, and going lower state.  Sensor reading: 0.000000 RPM.  Threshold value: 380.000000 RPM.

CRITICAL event: System Fan 1 reports the sensor is in a low, critical, and going lower state.  Sensor reading: 0.000000 RPM.  Threshold value: 320.000000 RPM.

 

Specs:

CategoryItem
MotherboardS5520HC
CPU2X Intel Xeon X560 @ 2.67GHz
CPUFans2X Intel E97383-002
↧

Bricked S2600G(L/Z)?

June 25, 2017, 8:05 am
$
0
0

Hi Guys,

 

So i was trying to upgrade firmware on my server.

I ran flashupdt -u  <package folder name>\flashupdt.cfg and went away when it was "Upgrading HBSP and PSU firmware..."

After i came back the server was running - fans were spinning but no signal on the screen. I left it running for couple of minutes but there was no change so i rebooted the server - it didn't come back.

System Status LED is solid Amber and 2nd,3rd green POST LED is on which means: 06h Early CPU initialisation during Sec Phase. and it stays like that forever.

I tried to swap CPUs, run with only one CPU (both CPUs tested) and the error is always the same.

 

Then i tried to flash using BIOS Recovery Procedure and i'm getting 1st,4th green LED on and 1st,2nd,3rd,4th Amber LED ON with 2 Beeps and 4 Beeps in the background.

I also tried different CPU configuration and nothing helps.

The only difference i see (i think so) is when i have USB drive inserted and not inserted.

When there's no USB Mass Storage beeps happens so quickly as described in the manual but when i insert the USB there's 1 second break between each set of beeps. Maybe i'm doing something wrong?

 

Does it means i bricked motherboard?

↧
↧

raw ipmi command to retrieve NIC 1 MAC address on S2600GZ

January 9, 2015, 10:19 am
$
0
0

Hi there,

 

what is the right approach to retrieve the NIC 1 MAC address (for OS usage) via IPMI?

 

NOTE: I am assuming the system is powered off and that a DHCP server assigned an IP address to the BMC LAN channel 1.

 

The S2600GZ technical product specification section 6.10.3.2.3 highlights the convention used to assign MAC address so conceptually one could calculate it from the BMC LAN channel 1 MAC address (by subtracting 4) but that seems brittle so I am looking for the (raw) IPMI command to provide that info directly!?

 

Other vendors implemented vendor-specific IPMI commands but I can't seem to find the doc that would cover an S2600GZ board..

 

Thanks & cheerio, Harry.

↧

first start problem

October 28, 2013, 7:25 am
$
0
0

I had created a operating software from bootable usb device but I am getting this error: "Initializing and Establishing Link"  . I am using a SR1550AL server and I thing I should disable network from bios but couldnt find disable option any help about it?

↧

Intel H2312JFJR - hardisks are not recognized

June 19, 2017, 12:24 am
$
0
0

Hi,

I bought an intel H2312JFJR system which came with 12 SCSI drives (2TB) and  four HNS2600JF Server Nodes.

When I first powered up the system, I noticed that non of the 12 hard disks is flashing any status light and when I get into the BIOS setup, no harddisk appeared in the boot order menu. This is the case for all the 4 nodes.

I tried to install a hypervisor (Xenserver) from the flash drive and it also confirmed that it could not find any drives. The only way I managed to get a node up and running is by using a flash drive with live Linux image.

I do not have any experience in Intel servers so I am not sure how to proceed.

What would cause all the 12 drives not working despite being a 4 node system with redundancy? and how should I proceed to further diagnose the problem ?

Regards,

Mishal

↧
Viewing all 3319 articles
Browse latest View live
Search

Latest Images

7 clever tricks Primark does to keep you walking & buying more than you need...

7 clever tricks Primark does to keep you walking & buying more than you need...

July 20, 2025, 5:14 am
Art for Everyone! Autism advocacy, local stories, and indigenous pride in one...

Art for Everyone! Autism advocacy, local stories, and indigenous pride in one...

July 20, 2025, 5:06 am
Paintings of English Downs 2

Paintings of English Downs 2

July 20, 2025, 4:30 am
How Kerala Women Rescued a Dying Forest and Turned It Into a Safe Haven for...

How Kerala Women Rescued a Dying Forest and Turned It Into a Safe Haven for...

July 20, 2025, 3:30 am
Met Eireann warns of heavy rain & spot flooding for DAYS before big...

Met Eireann warns of heavy rain & spot flooding for DAYS before big...

July 20, 2025, 1:14 am
Who is Kevin Lerena’s wife Geraldine?

Who is Kevin Lerena’s wife Geraldine?

July 20, 2025, 12:57 am
Man stabs woman, baby to death inside Queens home, police say

Man stabs woman, baby to death inside Queens home, police say

July 19, 2025, 11:00 pm
Ang papel ni whistleblower Julie Patidongan sa kaso ng mga nawawalang sabungero

Ang papel ni whistleblower Julie Patidongan sa kaso ng mga nawawalang sabungero

July 19, 2025, 9:45 pm
Telangana Human Rights Commission (TGHRC) seeks report from revenue dept on...

Telangana Human Rights Commission (TGHRC) seeks report from revenue dept on...

July 19, 2025, 7:29 pm
Crisis-hit NHS fat cats raking in MASSIVE salaries as frontline services cry...

Crisis-hit NHS fat cats raking in MASSIVE salaries as frontline services cry...

July 19, 2025, 2:11 pm
<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>