Hello,

my Intel S1200SPL is in a third party case an I got problems with the fan speed. I have two PWM fans and one with 3 pin.

The Fans with PWM spin to slow and the 3 pin fan spin withe 100%. How can I fix this?

I allready made a SDR update and choose "Other Case" and set the fans.

Hi,

I've just been given an ancient, refurbished S2600CP2J motherboard complete with CPUs and RAM and would like to get it fully working again.

The obvious first step is to update the BIOS but the oldest EFI update package available (01.02.003) states that I need to have at least version 01.01.1002 before starting or "the update process may render the system not operatable!"

According to the BIOS screen, my system is currently SE5C600.86B.99.99.x034, build date 08/23/2011.

As I have no wish to kill the system before I get started, is there any way of upgrading it to 01.01.1002 as a minimum?

Thanks.

I would like to update the BIOS on my S5000PSLSATAR in hopes to fix my fan speed problem. My current AMI bios is Aptio version 1.20.1093 and the bios listed in setup is S5000.86B.10.60.0091

I have download the 'Firmware Update Package for DOS, Version:101;68;48 dated 12/27/2010 I have read through the include BIOS101.txt file and I am not 100% sure my system meets the requirements. I have never tried to update the firmware on any of my Intel servers so I am hoping to avoid messing up my working server.

Can someone confirm this is the correct package for my mother board and if not, suggest or point out the correct one. It currently does not have any OS installed but I would like to convert to a backup server.

This is the zip file I download from Intel: S5000PSL_DOS_update_BIOS101_BMC68_FRUSDR48.zip

There are 3 LAN ports on this server board as baseboard LAN 1, baseboard LAN2 and Dedicated BMC LAN.  In the BIOS Setup Utility if you go to Server Management->BMC LAN Configuration you can see Baseboard Lan and Dedicated Management Lan configurations.  But there is only one Baseboard LAN referenced.  Why is the Baseboard LAN port 2 missing from ths screen?  Is there documentation that describes this?  In the BIOS Setup Utility doc the Baseboard LAN and Dedicated Management LAN are shown.  In Intel Server Board S2600ST Product Family Technical Product Specification ports 1 and 2 are referenced in the BIOS Setup Utility (6.4.1) but I couldn't find this myself in the BIOS Setup Utility.

Some of my users have concluded that this means Port 1 and Port 2 are shared when in actuality Port 1 is shared with the BMC and Port 2 is shared with the BMC, effectively giving 3 LAN ports with access to the BMC and 2 available to the OS.

Thanks for any assistance.

BobM

I have recently purchased three S1200SPOR servers, and they all three are having the same issue: at random intervals, the fans will spin up to max for just a second or two before settling back down. These intervals can be anywhere from a few minutes to an hour, and they do not correlate with server load.

I have upgraded the firmware to S1200SP.86B.03.01.0026.092720170729, check for thermal trips, and examined the SEL, but they didn't help. However, in watching the IPMI sensors, I did notice one correlation: the times when the fans spin up seem to correspond to the sensors being unable to read "P1 Therm Margin". My conclusion was that the system is occasionally unable to read the power supply temperature, so it spins up the fans "just in case", but on the next reading it reads the temperature correctly and so returns the fans to normal.

I checked the sensor wire and it is secure. (Fiddling with it doesn't trigger the fan response either.) I might conclude a hardware fault, but this is happening on all three systems, each of which were purchased at different times over the last few months.

I also found this thread: R1304SPOSHBNR 1U chassis fans randomly spin up to maximum for a few seconds and then go back to normal. but the information isn't any help since the SEL doesn't report any errors, the problem is intermittent, I don't have a RAID controller in them, and the standard checks didn't reveal anything promising.

If anyone has any ideas on where to go next, I would appreciate the input.

Thanks!

System info dump (all three set up the same):

OS: CentOS 7

# dmidecode

Getting SMBIOS data from sysfs.

SMBIOS 2.7 present.

64 structures occupying 3770 bytes.

Table at 0x80630000.

Handle 0x0006, DMI type 0, 24 bytes

BIOS Information

        Vendor: Intel Corporation

        Version: S1200SP.86B.03.01.0026.092720170729

        Release Date: 09/27/2017

        Address: 0xF0000

        Runtime Size: 64 kB

        ROM Size: 16384 kB

        Characteristics:

                PCI is supported

                PNP is supported

                BIOS is upgradeable

                BIOS shadowing is allowed

                Boot from CD is supported

                Selectable boot is supported

                EDD is supported

                5.25"/1.2 MB floppy services are supported (int 13h)

                3.5"/720 kB floppy services are supported (int 13h)

                3.5"/2.88 MB floppy services are supported (int 13h)

                Print screen service is supported (int 5h)

                8042 keyboard services are supported (int 9h)

                Serial services are supported (int 14h)

                Printer services are supported (int 17h)

                CGA/mono video services are supported (int 10h)

                ACPI is supported

                USB legacy is supported

                LS-120 boot is supported

                ATAPI Zip drive boot is supported

                BIOS boot specification is supported

                Function key-initiated network boot is supported

                Targeted content distribution is supported

                UEFI is supported

        BIOS Revision: 0.0

        Firmware Revision: 0.0

Handle 0x0007, DMI type 1, 27 bytes

System Information

        Manufacturer: Intel Corporation

        Product Name: S1200SP

        Version: R1304SPOSHBNR

        Serial Number: QSCD74200212

        UUID: 71C4BAF6-8AB0-E711-AB21-A4BF0128AAE2

        Wake-up Type: Power Switch

        SKU Number: SKU Number

        Family: Family

Handle 0x0008, DMI type 2, 17 bytes

Base Board Information

        Manufacturer: Intel Corporation

        Product Name: S1200SP

        Version: H57534-260

        Serial Number: QSSA74100091

        Asset Tag: Base Board Asset Tag

        Features:

                Board is a hosting board

                Board is replaceable

        Location In Chassis: Part Component

        Chassis Handle: 0x0000

        Type: Motherboard

        Contained Object Handles: 0

Handle 0x001D, DMI type 4, 48 bytes

Processor Information

        Socket Designation: CPU 1

        Type: Central Processor

        Family: Xeon

        Manufacturer: Intel(R) Corporation

        ID: E9 06 09 00 FF FB EB BF

        Signature: Type 0, Family 6, Model 158, Stepping 9

        Flags:

                FPU (Floating-point unit on-chip)

                VME (Virtual mode extension)

                DE (Debugging extension)

                PSE (Page size extension)

                TSC (Time stamp counter)

                MSR (Model specific registers)

                PAE (Physical address extension)

                MCE (Machine check exception)

                CX8 (CMPXCHG8 instruction supported)

                APIC (On-chip APIC hardware supported)

                SEP (Fast system call)

                MTRR (Memory type range registers)

                PGE (Page global enable)

                MCA (Machine check architecture)

                CMOV (Conditional move instruction supported)

                PAT (Page attribute table)

                PSE-36 (36-bit page size extension)

                CLFSH (CLFLUSH instruction supported)

                DS (Debug store)

                ACPI (ACPI supported)

                MMX (MMX technology supported)

                FXSR (FXSAVE and FXSTOR instructions supported)

                SSE (Streaming SIMD extensions)

                SSE2 (Streaming SIMD extensions 2)

                SS (Self-snoop)

                HTT (Multi-threading)

                TM (Thermal monitor supported)

                PBE (Pending break enabled)

        Version: Intel(R) Xeon(R) CPU E3-1220 v6 @ 3.00GHz

        Voltage: 0.9 V

        External Clock: 100 MHz

        Max Speed: 4200 MHz

        Current Speed: 3000 MHz

        Status: Populated, Enabled

        Upgrade: Other

        L1 Cache Handle: 0x001A

        L2 Cache Handle: 0x001B

        L3 Cache Handle: 0x001C

        Serial Number: To Be Filled By O.E.M.

        Asset Tag: To Be Filled By O.E.M.

        Part Number: To Be Filled By O.E.M.

        Core Count: 4

        Core Enabled: 4

        Thread Count: 4

        Characteristics:

                64-bit capable

                Multi-Core

                Execute Protection

                Enhanced Virtualization

                Power/Performance Control

Handle 0x000E, DMI type 17, 40 bytes

Memory Device

        Array Handle: 0x001E

        Error Information Handle: Not Provided

        Total Width: Unknown

        Data Width: Unknown

        Size: No Module Installed

        Form Factor: Unknown

        Set: None

        Locator: DIMM_A1

        Bank Locator: NODE 0 CHANNEL 0 DIMM 1

        Type: Unknown

        Type Detail: None

        Speed: Unknown

        Manufacturer: Empty/NO DIMM

        Serial Number: Not Specified

        Asset Tag: Not Specified

        Part Number: Not Specified

        Rank: Unknown

        Configured Clock Speed: Unknown

        Minimum Voltage: Unknown

        Maximum Voltage: Unknown

        Configured Voltage: Unknown

Handle 0x0010, DMI type 17, 40 bytes

Memory Device

        Array Handle: 0x001E

        Error Information Handle: Not Provided

        Total Width: 72 bits

        Data Width: 64 bits

        Size: 8192 MB

        Form Factor: DIMM

        Set: None

        Locator: DIMM_A2

        Bank Locator: NODE 0 CHANNEL 0 DIMM 2

        Type: DDR4

        Type Detail: Synchronous

        Speed: 2133 MHz

        Manufacturer: Kingston

        Serial Number: BA3287C7

        Asset Tag: DIMM_A2_AssetTag

        Part Number: 9965669-023.A00G

        Rank: 2

        Configured Clock Speed: 2133 MHz

        Minimum Voltage: Unknown

        Maximum Voltage: Unknown

        Configured Voltage: 1.2 V

Handle 0x001F, DMI type 17, 40 bytes

Memory Device

        Array Handle: 0x001E

        Error Information Handle: Not Provided

        Total Width: Unknown

        Data Width: Unknown

        Size: No Module Installed

        Form Factor: Unknown

        Set: None

        Locator: DIMM_B1

        Bank Locator: NODE 0 CHANNEL 1 DIMM 1

        Type: Unknown

        Type Detail: None

        Speed: Unknown

        Manufacturer: Empty/NO DIMM

        Serial Number: Not Specified

        Asset Tag: Not Specified

        Part Number: Not Specified

        Rank: Unknown

        Configured Clock Speed: Unknown

        Minimum Voltage: Unknown

        Maximum Voltage: Unknown

        Configured Voltage: Unknown

Handle 0x0020, DMI type 17, 40 bytes

Memory Device

        Array Handle: 0x001E

        Error Information Handle: Not Provided

        Total Width: Unknown

        Data Width: Unknown

        Size: No Module Installed

        Form Factor: Unknown

        Set: None

        Locator: DIMM_B2

        Bank Locator: NODE 0 CHANNEL 1 DIMM 2

        Type: Unknown

        Type Detail: None

        Speed: Unknown

        Manufacturer: Empty/NO DIMM

        Serial Number: Not Specified

        Asset Tag: Not Specified

        Part Number: Not Specified

        Rank: Unknown

        Configured Clock Speed: Unknown

        Minimum Voltage: Unknown

        Maximum Voltage: Unknown

        Configured Voltage: Unknown

# sensors

acpitz-virtual-0

Adapter: Virtual device

temp1:        +27.8°C  (crit = +119.0°C)

temp2:        +29.8°C  (crit = +119.0°C)

coretemp-isa-0000

Adapter: ISA adapter

Physical id 0:  +44.0°C  (high = +80.0°C, crit = +100.0°C)

Core 0:         +39.0°C  (high = +80.0°C, crit = +100.0°C)

Core 1:         +40.0°C  (high = +80.0°C, crit = +100.0°C)

Core 2:         +42.0°C  (high = +80.0°C, crit = +100.0°C)

Core 3:         +44.0°C  (high = +80.0°C, crit = +100.0°C)

power_meter-acpi-0

Adapter: ACPI interface

power1:       36.00 W  (interval = 4294967.29 s)

# ipmitool sdr elist full

System Airflow   | 11h | ok  | 23.1 | 8 CFM

BB P1 VR Temp    | 20h | ok  |  7.1 | -74 degrees C

P1 VR Ctrl Temp  | BAh | ok  |  7.1 | 31 degrees C

Front Panel Temp | 21h | ok  | 12.1 | 23 degrees C

SSB Temp         | 22h | ok  |  7.1 | 32 degrees C

BB Inlet Temp    | 23h | ok  |  7.1 | 22 degrees C

BB BMC Temp      | 24h | ok  |  7.1 | 30 degrees C

BB Mem VR temp   | 25h | ok  |  7.1 | -75 degrees C

HSBP 1 Temp      | 29h | ok  | 15.1 | 24 degrees C

Exit Air Temp    | 2Eh | ok  |  7.1 | 28 degrees C

System Fan 1     | 34h | ok  | 29.1 | 5978 RPM

System Fan 2     | 31h | ok  | 29.2 | 5978 RPM

System Fan 3     | 32h | ok  | 29.3 | 5978 RPM

PS1 Input Power  | 54h | ok  | 10.3 | 35 Watts

PS1 Temperature  | 5Ch | ok  | 10.1 | 41 degrees C

P1 Therm Margin  | 74h | ok  |  3.1 | -55 degrees C <----- this will say "No Reading" rather than "-55 degrees C" when the fans spin up, then back to "-55 degrees C" when the fans spin back down

P1 Therm Ctrl %  | 78h | ok  |  3.1 | 0 percent

P1 DTS Therm Mgn | 83h | ok  |  3.1 | -34 degrees C

DIMM Thrm Mrgn 1 | B0h | ok  |  8.1 | -60 degrees C

Agg Therm Mgn 1  | C8h | ok  |  7.1 | -12 degrees C

BB +12.0V        | D0h | ok  |  7.1 | 12.10 Volts

BB +3.3V Vbat    | DEh | ok  |  7.1 | 3.08 Volts

MTT CPU1         | 34h | ok  |  3.1 | 0 percent

(I have had fan spin-ups since the last system boot show here)

#ipmitool sel elist

   1 | 12/12/2017 | 16:15:21 | Event Logging Disabled System Event Log | Log area reset/cleared | Asserted

   2 | 12/12/2017 | 19:49:35 | Power Unit Pwr Unit Status | Power off/down | Asserted

   3 | 12/13/2017 | 15:36:02 | Processor P1 Status | Presence detected | Asserted

   4 | 12/13/2017 | 15:36:09 | Drive Slot / Bay HDD 0 Status | Drive Present | Asserted

   5 | 12/13/2017 | 15:36:09 | Drive Slot / Bay HDD 1 Status | Drive Present | Asserted

   6 | 12/13/2017 | 15:36:29 | System Event BIOS Evt Sensor | OEM System boot event | Asserted

   7 | 12/13/2017 | 15:54:26 | Power Supply PS1 Status | Presence detected | Deasserted

   8 | 12/13/2017 | 15:54:31 | Physical Security #0x04 | General Chassis intrusion | Asserted

   9 | 12/13/2017 | 15:54:35 | Fan #0x30 | Lower Non-critical going low  | Asserted

   a | 12/13/2017 | 15:54:35 | Fan #0x30 | Lower Critical going low  | Asserted

   b | 12/13/2017 | 15:54:35 | Fan #0x33 | Lower Non-critical going low  | Asserted

   c | 12/13/2017 | 15:54:35 | Fan #0x33 | Lower Critical going low  | Asserted

   d | 12/13/2017 | 15:54:36 | Physical Security #0x04 | General Chassis intrusion | Deasserted

   e | 12/13/2017 | 15:54:36 | Fan #0x30 | Lower Non-critical going low  | Deasserted

   f | 12/13/2017 | 15:54:36 | Fan #0x30 | Lower Critical going low  | Deasserted

  10 | 12/13/2017 | 15:54:36 | Fan #0x33 | Lower Non-critical going low  | Deasserted

  11 | 12/13/2017 | 15:54:36 | Fan #0x33 | Lower Critical going low  | Deasserted

  12 | 12/13/2017 | 21:53:14 | Power Unit Pwr Unit Status | Power off/down | Asserted

  13 | 12/14/2017 | 15:15:22 | Processor P1 Status | Presence detected | Asserted

  14 | 12/14/2017 | 15:15:28 | Drive Slot / Bay HDD 0 Status | Drive Present | Asserted

  15 | 12/14/2017 | 15:15:28 | Drive Slot / Bay HDD 1 Status | Drive Present | Asserted

  16 | 12/14/2017 | 15:15:47 | System Event BIOS Evt Sensor | OEM System boot event | Asserted

  17 | 12/14/2017 | 15:36:49 | Power Unit Pwr Unit Status | Power off/down | Asserted

  18 | 12/14/2017 | 15:36:52 | Power Unit Pwr Unit Status | Power off/down | Deasserted

  19 | 12/14/2017 | 15:37:17 | System Event BIOS Evt Sensor | OEM System boot event | Asserted

Hello,

I have the current problem:

I have an INTEL S5000PSL installed with 16GB RAM (4x4) and two Xeon 51xx. The MoBo is installed in an Intel Chassis SC5400 (I don´t know the exactly model and don´t know how to identify)

The Problem is that all Fans running at 100% all the time after the newest BIOS UPDATE (Download Firmware Update Package for DOS ). The settings in Bios were loaded to optimzied settings (F9) and the Fanspeed to Acoustic, 0-300.

I had also resetted the CMOS and the BMC jumper but no solution....

I had recognized that the SYSTEM_STATUS_LED is currently blinking orange/amber all the time also when WIN SERVER 2012 R2 is running.

The SYS_FAN_LED (left back near by RAM) is also lightning in amber but I have installed an 4-PIN PWM Fan....

I don´t know what I can do else. Do you have any information how I can get the fan´s silent/running in Idle mode?

Thanks in advance

Customer wants to know MTBF of some intel components.

How can I find out MTBF of following components?

1. S7200AP

2. S2600BPB

3. S2600WF0

4. Intel OPA Director Class Switch 100 Series-24 slot chassis

5. Intel OPA Edge Switch - 100 Series 48 Ports

6. INTEL OMNI PATH STANDARD REACH PASSIVE COPPER CABLE

7. INTEL OMNI PATH 1:1 OPTICAL CABLE

8. Intel(R) Xeon Phi(TM) CPU 7250 @ 1.40GHz

9. Intel(R) Xeon(R) Gold 6148 CPU @ 2.40GHz

10. INTEL® OMNI-PATH HOST FABRIC INTERFACE ADAPTER 100 SERIES 1 PORT PCIE X16 LOW PROFILE

11. INTEL 10GIGE, COPPER, 2 PORT, X710-DA2, PCIE3.0 X8 - 8 GT/S, FH & LP, SFP+ COPPER

Good Day.

I am tried enable "OS boot watchdog timer" at BIOS, but my OS (Window 10 - 1709) always rebooted.

I didnt find Intel Watchdog driver and i dont understand how i should install it.

I am really need your help.

How i should check this driver? Does this function support Windows 10?

Hello,

my Intel S1200SPL is in a third party case an I got problems with the fan speed. I have two PWM fans and one with 3 pin.

The Fans with PWM spin to slow and the 3 pin fan spin withe 100%. How can I fix this?

I allready made a SDR update and choose "Other Case" and set the fans.

Hello,

I have a server mothebord S3420GP with 6 memory slots.

Now, I have 2 slots filled with these: 2x KINGSTON 4GB 1333MHz DDR3 ECC CL9 DIMM with Thermal Sensor.

Is possible to use another 4 these RAMs? So I would have 24 GB RAM with 6 x 4 GB. Is this combination possible?

Or is possible to use 4 x KINGSTON 8GB DDR3 1333MHz CL9 ECC Dual Rank BOX.

So total memory size will be 32 GB RAM.

Thanks for any answers.

Hello!

Recently bought Quanta DA0F03MBCE0 X79 C602 with Dual E5 2680 v2.

unfortunately seller did not provide any software / drivers...

allready installed drivers for C602 chipset https://downloadcenter.intel.com/product/63984/Intel-C602-Chipset

but still so many unknown devices in the Device Manager after Windows 10 installation

http://www.picshare.ru/view/8787973/

full list of unknown Devices IDs:

PCI\VEN_8086&DEV_0E1A&CC_0880

PCI\VEN_8086&DEV_0E11&CC_0880

PCI\VEN_8086&DEV_0E19&CC_0880

PCI\VEN_8086&DEV_0E15&CC_0880

PCI\VEN_8086&DEV_0E12&CC_0880

PCI\VEN_8086&DEV_0E16&CC_0880

PCI\VEN_8086&DEV_0E96&CC_0880

PCI\VEN_8086&DEV_0E86&CC_0880

PCI\VEN_8086&DEV_0E1B&CC_0880

PCI\VEN_8086&DEV_0E14&CC_0880

PCI\VEN_8086&DEV_1D3D&CC_0700

PCI\VEN_8086&DEV_0E39&CC_1101

they all started with pci\ven_8086

and as i noticed it belongs to Intel

please help me and provide any software / drivers!

topic at the russian forum with photos:

DA0F03MBCE0 X79 C602 Dual E5 2680 v2 - Технический форум

Hello,

I'm looking at the Readme and Update Instructions that come with S2600ST_EFI_BIOSR0009_ME04.00.04.288.0_BMC1.29.7d703f59_FRUSDR_1.24.  There is a statement that says:

############################################################################

uEFI System Update Package (SUP) Installation and Operation Instructions

Released - October 27, 2017

********************************************************************************

This update package includes the following production level system firmware

updates:

  System BIOS  -   00.01.0009

  ME Firmware  - 04.00.04.288

  BMC Firmware - 1.29.7d703f59

  FRUSDR       - 1.24

--- Supported Products ---

Intel(R) Server Board S2600ST Family

Important notes:

WARNING: This release has the BMC PCIe bridge disabled. This will cause the

    majority of operating systems to fail at boot as they stall during video

    driver initialization.

############################################################################

Which FW element has the BMC PCIe bridge disabled, the BIOS or the BMC?  We're using a 3rd party BMC provider and I need to know if this is something I can have them address or not.

Thanks.

Bob

There are 3 LAN ports on this server board as baseboard LAN 1, baseboard LAN2 and Dedicated BMC LAN.  In the BIOS Setup Utility if you go to Server Management->BMC LAN Configuration you can see Baseboard Lan and Dedicated Management Lan configurations.  But there is only one Baseboard LAN referenced.  Why is the Baseboard LAN port 2 missing from ths screen?  Is there documentation that describes this?  In the BIOS Setup Utility doc the Baseboard LAN and Dedicated Management LAN are shown.  In Intel Server Board S2600ST Product Family Technical Product Specification ports 1 and 2 are referenced in the BIOS Setup Utility (6.4.1) but I couldn't find this myself in the BIOS Setup Utility.

Some of my users have concluded that this means Port 1 and Port 2 are shared when in actuality Port 1 is shared with the BMC and Port 2 is shared with the BMC, effectively giving 3 LAN ports with access to the BMC and 2 available to the OS.

Thanks for any assistance.

BobM

Hi, i have been playing with the RAID in the hardware (Server is in UEFI mode) (i have not lost data, only test systems).  We cant get in to the BIOS due to the below, so how do we get out of this loop (without removing the RAID hardware card), there must be an answer that works to open the BIOS / RAID utility

Please see images:

We had CACHECADE setup (and still connected), now we have the below message:

"There are offline or missing virtual drives with preserved cache.  Please check the cable and ensure that all the drives are present, Press any key to enter the configuration utility."

No matter what we enter (Y, N, C, R, F) the next screen says:

All Driver Health Status List !

Good Day.

I am tried enable "OS boot watchdog timer" at BIOS, but my OS (Window 10 - 1709) always rebooted.

I didnt find Intel Watchdog driver and i dont understand how i should install it.

I am really need your help.

How i should check this driver? Does this function support Windows 10?

Hello,

I have the current problem:

I have an INTEL S5000PSL installed with 16GB RAM (4x4) and two Xeon 51xx. The MoBo is installed in an Intel Chassis SC5400 (I don´t know the exactly model and don´t know how to identify)

The Problem is that all Fans running at 100% all the time after the newest BIOS UPDATE (Download Firmware Update Package for DOS ). The settings in Bios were loaded to optimzied settings (F9) and the Fanspeed to Acoustic, 0-300.

I had also resetted the CMOS and the BMC jumper but no solution....

I had recognized that the SYSTEM_STATUS_LED is currently blinking orange/amber all the time also when WIN SERVER 2012 R2 is running.

The SYS_FAN_LED (left back near by RAM) is also lightning in amber but I have installed an 4-PIN PWM Fan....

I don´t know what I can do else. Do you have any information how I can get the fan´s silent/running in Idle mode?

Thanks in advance

Hello,

my Intel S1200SPL is in a third party case an I got problems with the fan speed. I have two PWM fans and one with 3 pin.

The Fans with PWM spin to slow and the 3 pin fan spin withe 100%. How can I fix this?

I allready made a SDR update and choose "Other Case" and set the fans.

Hi, i have been playing with the RAID in the hardware (Server is in UEFI mode) (i have not lost data, only test systems).  We cant get in to the BIOS due to the below, so how do we get out of this loop (without removing the RAID hardware card), there must be an answer that works to open the BIOS / RAID utility

Please see images:

We had CACHECADE setup (and still connected), now we have the below message:

"There are offline or missing virtual drives with preserved cache.  Please check the cable and ensure that all the drives are present, Press any key to enter the configuration utility."

No matter what we enter (Y, N, C, R, F) the next screen says:

All Driver Health Status List !

Customer wants to know MTBF of some intel components.

How can I find out MTBF of following components?

1. S7200AP

2. S2600BPB

3. S2600WF0

4. Intel OPA Director Class Switch 100 Series-24 slot chassis

5. Intel OPA Edge Switch - 100 Series 48 Ports

6. INTEL OMNI PATH STANDARD REACH PASSIVE COPPER CABLE

7. INTEL OMNI PATH 1:1 OPTICAL CABLE

8. Intel(R) Xeon Phi(TM) CPU 7250 @ 1.40GHz

9. Intel(R) Xeon(R) Gold 6148 CPU @ 2.40GHz

10. INTEL® OMNI-PATH HOST FABRIC INTERFACE ADAPTER 100 SERIES 1 PORT PCIE X16 LOW PROFILE

11. INTEL 10GIGE, COPPER, 2 PORT, X710-DA2, PCIE3.0 X8 - 8 GT/S, FH & LP, SFP+ COPPER

Good Day.

I am tried enable "OS boot watchdog timer" at BIOS, but my OS (Window 10 - 1709) always rebooted.

I didnt find Intel Watchdog driver and i dont understand how i should install it.

I am really need your help.

How i should check this driver? Does this function support Windows 10?