Hello,
I have a server mothebord S3420GP with 6 memory slots.
Now, I have 2 slots filled with these: 2x KINGSTON 4GB 1333MHz DDR3 ECC CL9 DIMM with Thermal Sensor.
Is possible to use another 4 these RAMs? So I would have 24 GB RAM with 6 x 4 GB. Is this combination possible?
Or is possible to use 4 x KINGSTON 8GB DDR3 1333MHz CL9 ECC Dual Rank BOX.
So total memory size will be 32 GB RAM.
Thanks for any answers.
I had created a operating software from bootable usb device but I am getting this error: "Initializing and Establishing Link" . I am using a SR1550AL server and I thing I should disable network from bios but couldnt find disable option any help about it?
Hello,
I went accross 2x E5-2696v2 processors and tried to use them in one of our work stations based on S2600CP or S2600CP4 motherboards. Unfortunately neither of the computers worked with those CPU's. Both of the computers worked fine with 2690 v1 and 2667 v2 though. So my question is: should the two platforms work with E5-2696v2 processors?
more specific information about platforms:
Chipset: Intel C602 rev. 06
Mainboard Model: S2600CP (0x000001AE - 0x005368B0)
revision: E99552-510
serial: QSCP34300402
BIOS: SE5C600.86B.02.02.0002.122320131210 dated at 12/23/2013
where minimum required bios is ver. 02.01.0002 from 09/07/2013
the list of compatible processors is: http://www.intel.com/support/motherboards/server/sb/CS-033241.htm
where 2696v2 does no appear.
looking forward your help.
regards
janusz
Hi
Hoping for some help to regain the psu reduncy on our P4208CP4MGHC system.
Everything is original and untampered.
During bios updates last night using OFU I noticed these messages:
C:\flashupdt\04>flashupdt -u flashupdt.cfg
One Boot Flash Update Utility Version 13.1 Build 5
Copyright (c) 2015 Intel Corporation
SDR Auto-Configuration is not supported on this platform.
Update file Configuration: XXX S2600CP,2.0
Processing capsule file - .\R02.04.0003.cap
Processing capsule file - .\MEComplete_02.01.07.328.cap
Update file Configuration: Master.cfg, Rev 1.11
S2600CP platform FRU & SDR package version 1.11
Intel(R) Server Board S2600CP platform
Copyright (c) 2010 - 2012 Intel Corporation
Select the function you desire to perform:
1 Update only the SDR repository
2 Update only the FRU repository
3 Update both the FRU and the SDR repository
4 Modify the Product Asset Tag
5 Exit
3
Intel(R) Server Chassis P4000M Redundant Fan SKU is detected
Power supply 1 FRU is invalid.
Power supply 2 FRU is invalid.
8 X 2.5 Hot Swap Backplane 1 is detected.
Probing system for sensors and FRU device hardware...
----------------------------------------------------------------------------------------
After succesful completion of the flash and reboot we have this in the event log:
EventID:1099 Time Stamp:05/29/2015 00:44:59 SensorName:Pwr Unit Redund Sensor Type:Power Unit Description:reports redundancy has been lost -Asserted
EventID:1100 Time Stamp:05/29/2015 00:44:59 SensorName:Pwr Unit Redund Sensor Type:Power Unit Description:reports redundancy has been lost, but the unit is still functioning with the minimum amount of resources needed for normal operation -Asserted
-----------------------------------------------------------
In the BMC web console server health I see this:
| Pwr Unit Status | All deasserted | OK | 0x0000 |
| Pwr Unit Redund | reports redundancy has been lost reports redundancy has been lost, but the unit is still functioning with the minimum amount of resources needed for normal operation | Warning | 0x000A |
-------------------------------------------------------------
Is it something in relation to running the updates via OFU and the message stated immediately after starting the update sequece?:
"SDR Auto-Configuration is not supported on this platform"
Would rerunning the update package in EFI help the recognition of the psu´s?
Please if anyone has suggestions on how to work this out chip in.
Best Regards Peter
S1200BTLR use Intel(R) Xeon(R) CPU E3-1230 V2 @ 3.30GHz,ipmi-sel output:
[root@T58 ~]# ipmi-sel
ID | Date | Time | Name | Type | Event
1 | May-30-2015 | 11:16:30 | System Event Log | Event Logging Disabled | Log Area Reset/Cleared
2 | May-30-2015 | 11:20:16 | BB P1 Vcc | Voltage | Lower Non-critical - going low ; Sensor Reading = 0.64 V ; Threshold = 0.64 V
3 | May-30-2015 | 11:20:17 | BB P1 Vcc | Voltage | Lower Non-critical - going low ; Sensor Reading = 0.73 V ; Threshold = 0.64 V
4 | May-30-2015 | 11:20:58 | BB P1 Vcc | Voltage | Lower Non-critical - going low ; Sensor Reading = 0.64 V ; Threshold = 0.64 V
5 | May-30-2015 | 11:20:59 | BB P1 Vcc | Voltage | Lower Non-critical - going low ; Sensor Reading = 0.67 V ; Threshold = 0.64 V@
Hello,
I have an S1200BTL motherboard and an P4303xxsfcnna chassis. I've used Intel Deployment Assistant to update BIOS, BMC, FRU, etc. The chassis fans are still running at full speed. The BIOS only has an option to change to altitude, but the fan speed is set to auto and cannot be configured.
Any reason why the fans would be running full speed on both of my systems?
Thanks
So I went to configure adapter teaming and had nothing but problems. The wizard would start the process, create the Intel Advanced Network Services Virtual Adapter, then hang and not complete any other parts of the process. I found out that I was using the wrong version of the software for my adapters (which are Pro/1000 MT Dual Port), installed an older version, and all was good to go... except for the 4 Virtual adapters that were created previously by failed attempts of the wizard. How do I remove these unused virtual adapters from the server? Simply trying to uninstall them via the device manager doesn't work. Neither did removing the teaming software, rebooting the server, or simply trying to delete the network connection.
It says system degraded and all the hard disk lights on the front are red. How can I locate which disk failed. I have a little bit unix experience. I mainly use windows. Since it is degraded, I should be able to recover the files or copy of them if I can bring the system back.
Free | 0 B |
|---|---|
Used | 0 B |
Backup | 0 B |
| Total Space | 0 B |
05/31/2015 7:32 pm
storage Status
| Status Messages | |
|---|---|
 | 4 disks on your storage device have incorrect data on them. Data on the storage device is available but may be lost if another disk fails. Click here to authorize overwriting existing data.
|
| Disk | Size |
|---|---|
 Disk 1 (ST31500541AS) | 1.4 TB |
| Disk 2 (ST31500541AS) | 1.4 TB |
| Disk 3 (ST31500541AS) | 1.4 TB |
| Disk 4 (ST31500541AS) | 1.4 TB |
Always disabled
None Connected
Click an icon or link to get detailed status information on the device, peripherals, and backups.
A green check means that everything is normal. If a yellow warning, or red error icon appears, your attention is required. Click the link to learn more about the problem or how to
I had created a operating software from bootable usb device but I am getting this error: "Initializing and Establishing Link" . I am using a SR1550AL server and I thing I should disable network from bios but couldnt find disable option any help about it?
i have a tyan s7025 with two xeon 5520 . i installed win 7 x64 ultimate and win 8 pro x64 .
with win 7 if i use the command : netsh int tcp show global then the result is :
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:\Windows\system32>netsh int tcp show global
Querying active state...
TCP Global Parameters
----------------------------------------------
Receive-Side Scaling State : enabled
Chimney Offload State : enabled
NetDMA State : enabled
Direct Cache Acess (DCA) : enabled
Receive Window Auto-Tuning Level : normal
Add-On Congestion Control Provider : ctcp
ECN Capability : disabled
RFC 1323 Timestamps : disabled
while with with 8 on the same mainboard with drivers being latest too , i get :
Microsoft Windows [Version 6.2.9200]
(c) 2012 Microsoft Corporation. All rights reserved.
C:\Windows\system32>netsh int tcp show global
Querying active state...
TCP Global Parameters
----------------------------------------------
Receive-Side Scaling State : enabled
Chimney Offload State : disabled
NetDMA State : disabled
Direct Cache Access (DCA) : disabled
Receive Window Auto-Tuning Level : normal
Add-On Congestion Control Provider : none
ECN Capability : disabled
RFC 1323 Timestamps : disabled
Initial RTO : 3000
Receive Segment Coalescing State : disabled
despite i added in registry some new keys :
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters
EnableDCA=1 and EnableTCPA=1
they have no effect even many reboot ... while my settings in win 7 were done without anything in the registry except using tcpoptimizer from speed guide
what should i do ?
i also be glad if someone gives a link to a wiki about the registry keys for tcip and the different windows releases, even something [improbable] knowing all the keys of all the windows...
Hello,
I have a server mothebord S3420GP with 6 memory slots.
Now, I have 2 slots filled with these: 2x KINGSTON 4GB 1333MHz DDR3 ECC CL9 DIMM with Thermal Sensor.
Is possible to use another 4 these RAMs? So I would have 24 GB RAM with 6 x 4 GB. Is this combination possible?
Or is possible to use 4 x KINGSTON 8GB DDR3 1333MHz CL9 ECC Dual Rank BOX.
So total memory size will be 32 GB RAM.
Thanks for any answers.
I have a JBOD2312S2SP Intel Raid Enclosure (Intel® Storage Systems JBOD Family) at my house and woke up to screaming fan noises. Warning light was blinking and the console showed this:
ID = 206
SEQUENCE NUMBER = 164362
TIME = 29-06-2013 03:13:39
LOCALIZED MESSAGE = Controller ID: 0 Power supply cable removed on enclosure: 1 Power Supply 1
Note I only have one power supply so if the cable was removed not sure how it was still running. Right after that warning received the below messages copied from the logs so the top one is the latest:
ID = 243
SEQUENCE NUMBER = 164371
TIME = 29-06-2013 03:13:44
LOCALIZED MESSAGE = Controller ID: 0 Fan speed changed on enclosure: 1 Fan 3
ID = 243
SEQUENCE NUMBER = 164370
TIME = 29-06-2013 03:13:44
LOCALIZED MESSAGE = Controller ID: 0 Fan speed changed on enclosure: 1 Fan 2
ID = 243
SEQUENCE NUMBER = 164369
TIME = 29-06-2013 03:13:44
LOCALIZED MESSAGE = Controller ID: 0 Fan speed changed on enclosure: 1 Fan 1
ID = 243
SEQUENCE NUMBER = 164368
TIME = 29-06-2013 03:13:42
LOCALIZED MESSAGE = Controller ID: 0 Fan speed changed on enclosure: 1 Fan 3
ID = 243
SEQUENCE NUMBER = 164367
TIME = 29-06-2013 03:13:42
LOCALIZED MESSAGE = Controller ID: 0 Fan speed changed on enclosure: 1 Fan 2
ID = 243
SEQUENCE NUMBER = 164366
TIME = 29-06-2013 03:13:42
LOCALIZED MESSAGE = Controller ID: 0 Fan speed changed on enclosure: 1 Fan 1
ID = 243
SEQUENCE NUMBER = 164365
TIME = 29-06-2013 03:13:40
LOCALIZED MESSAGE = Controller ID: 0 Fan speed changed on enclosure: 1 Fan 3
ID = 243
SEQUENCE NUMBER = 164364
TIME = 29-06-2013 03:13:40
LOCALIZED MESSAGE = Controller ID: 0 Fan speed changed on enclosure: 1 Fan 2
ID = 243
SEQUENCE NUMBER = 164363
TIME = 29-06-2013 03:13:40
LOCALIZED MESSAGE = Controller ID: 0 Fan speed changed on enclosure: 1 Fan 1
Last message until 6 minutes later I powered up a computer to remove in and shutdown the system. Pulled the power plug, put it back in, powered everything up, and it's running right now without issue. Thoughts?
Edit: As a side note, the Intel Raid Web Console shows this drive cage with 2 power supplies. Always did. I only have one. So not sure if that's just how many it can hold or if it's just not intelligent enough to detect the number of drives.
Thanks.
Steve
It says system degraded and all the hard disk lights on the front are red. How can I locate which disk failed. I have a little bit unix experience. I mainly use windows. Since it is degraded, I should be able to recover the files or copy of them if I can bring the system back.
Free | 0 B |
|---|---|
Used | 0 B |
Backup | 0 B |
| Total Space | 0 B |
05/31/2015 7:32 pm
storage Status
| Status Messages | |
|---|---|
| 4 disks on your storage device have incorrect data on them. Data on the storage device is available but may be lost if another disk fails. Click here to authorize overwriting existing data.
|
| Disk | Size |
|---|---|
| Disk 1 (ST31500541AS) | 1.4 TB |
| Disk 2 (ST31500541AS) | 1.4 TB |
| Disk 3 (ST31500541AS) | 1.4 TB |
| Disk 4 (ST31500541AS) | 1.4 TB |
Always disabled
None Connected
Click an icon or link to get detailed status information on the device, peripherals, and backups.
A green check means that everything is normal. If a yellow warning, or red error icon appears, your attention is required. Click the link to learn more about the problem or how to
can anyone tell me it the E3-1246 V3 is compatible with the P4304BTLSFCNR server system?
Hi all my server has been working fine for about 4 Months now and I decided to input the driver disk to run a bios update check. it told me one was available and asked me to select where the source should come from I selected Intel download site and clicked next it hit to a point it was asking me what board I had an I couldn't remember off the top of my head so I told it to exit the process and then it froze so I had to reboot and now it powers on but I don't get any beep codes or bios splash screen. I've tried to flash the CMOS but nothing has change how do I get a Bios recovery image like the manual is referring too
Hi
Hoping for some help to regain the psu reduncy on our P4208CP4MGHC system.
Everything is original and untampered.
During bios updates last night using OFU I noticed these messages:
C:\flashupdt\04>flashupdt -u flashupdt.cfg
One Boot Flash Update Utility Version 13.1 Build 5
Copyright (c) 2015 Intel Corporation
SDR Auto-Configuration is not supported on this platform.
Update file Configuration: XXX S2600CP,2.0
Processing capsule file - .\R02.04.0003.cap
Processing capsule file - .\MEComplete_02.01.07.328.cap
Update file Configuration: Master.cfg, Rev 1.11
S2600CP platform FRU & SDR package version 1.11
Intel(R) Server Board S2600CP platform
Copyright (c) 2010 - 2012 Intel Corporation
Select the function you desire to perform:
1 Update only the SDR repository
2 Update only the FRU repository
3 Update both the FRU and the SDR repository
4 Modify the Product Asset Tag
5 Exit
3
Intel(R) Server Chassis P4000M Redundant Fan SKU is detected
Power supply 1 FRU is invalid.
Power supply 2 FRU is invalid.
8 X 2.5 Hot Swap Backplane 1 is detected.
Probing system for sensors and FRU device hardware...
----------------------------------------------------------------------------------------
After succesful completion of the flash and reboot we have this in the event log:
EventID:1099 Time Stamp:05/29/2015 00:44:59 SensorName:Pwr Unit Redund Sensor Type:Power Unit Description:reports redundancy has been lost -Asserted
EventID:1100 Time Stamp:05/29/2015 00:44:59 SensorName:Pwr Unit Redund Sensor Type:Power Unit Description:reports redundancy has been lost, but the unit is still functioning with the minimum amount of resources needed for normal operation -Asserted
-----------------------------------------------------------
In the BMC web console server health I see this:
| Pwr Unit Status | All deasserted | OK | 0x0000 |
| Pwr Unit Redund | reports redundancy has been lost reports redundancy has been lost, but the unit is still functioning with the minimum amount of resources needed for normal operation | Warning | 0x000A |
-------------------------------------------------------------
Is it something in relation to running the updates via OFU and the message stated immediately after starting the update sequece?:
"SDR Auto-Configuration is not supported on this platform"
Would rerunning the update package in EFI help the recognition of the psu´s?
Please if anyone has suggestions on how to work this out chip in.
Best Regards Peter
I was trying to install Ubuntu 14.04LTS, 15.04 and CentOS 7, 7.1 on my S2600CP2 server board based system for several days. With Ubuntu 14.04 or higher, install procedure was terminated shortly after the Ubuntu logo showed up, showing the error message: “ i8042 no controller found”. With Centos 7 or higher, after choosing “install Centos 7”, same error showed and the computer restarted.
I learned later this error has something to do with PS/2 mouse or keyboard. In the bios setup, set “Port 60/64 Emulation” to be Disabled, all went well until the installation setup options for both Ubuntu 14.04 and Centos 7, but usb keyboard and mouse are disabled, I can’t choose an option or type in anything. Then have to reboot use the power button.
Please help me with this, there must be a way to solve this problem. Thanks in advance.
Hi I have an old S5000PSL server. Am trying to use Intel Deployment Assistant (most recent version 014). Got the ISO image and transferred to USB as a bootable image using Rufus. When I boot, I get the splash screen saying that the application is loading, then a text screen indicating that it's unable to access the boot device and whether it should restart. A restart of course yields the same result. Any thoughts or suggestions would be most appreciated.
We have server with motherboard Intel ® S2600CP & Windows Server 2008
RAID WEB Console 2 Utility for Windows* (https://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=23482&lang=rus&OSVersion=Windows%20Server%202008*&DownloadType= ) is installed. When it launched, console does not discover local server with message "Server could not be found because server may be down or server not itstalled in the host system"
I use settings local server or IP address my server.
Please help me.
Hi there,
what is the right approach to retrieve the NIC 1 MAC address (for OS usage) via IPMI?
NOTE: I am assuming the system is powered off and that a DHCP server assigned an IP address to the BMC LAN channel 1.
The S2600GZ technical product specification section 6.10.3.2.3 highlights the convention used to assign MAC address so conceptually one could calculate it from the BMC LAN channel 1 MAC address (by subtracting 4) but that seems brittle so I am looking for the (raw) IPMI command to provide that info directly!?
Other vendors implemented vendor-specific IPMI commands but I can't seem to find the doc that would cover an S2600GZ board..
Thanks & cheerio, Harry.
